Water Eject & Speaker Cleaner Sound

Play a 165 Hz water eject sound to remove water from your speaker in 30 seconds.

On iPhone, switch the Ring/Silent switch off — the tone has to play through the speaker.

Cleaning mode

  • Bluetooth off
  • Volume 100%
  • Speaker down

Steady 165 Hz sine wave at your device’s resonant frequency.

Ready when you are

Device preset

Base 165 Hz

Channel

165 Hz

Stop where the speaker buzzes loudest — its resonant frequency.

A 3-second chime to check for muffled or distorted audio.

Tilt guide

Let gravity help

Hold the phone at 45–90°, bottom speaker port facing the floor.

Tilt the laptop forward or onto its side so the grilles face the desk.

Hold the phone with the top earpiece facing the floor, screen toward you.

Keep the port pointing down for the whole cycle. Acoustic pressure loosens the droplets; gravity takes them out.

How to Eject Water from iPhone & Android

Five steps, about a minute in total. Do them in order as soon as the phone gets wet.

  1. 01

    Power off and unplug

    Unplug the charger, take the case off, and switch the phone off if it was fully submerged.

  2. 02

    Blot the outside dry

    Wipe the frame, ports and grille with a lint-free cloth. Never push fabric into the speaker.

  3. 03

    Disconnect Bluetooth and max the volume

    Turn off earbuds or a speaker and set media volume to 100% so the tone reaches the wet driver.

  4. 04

    Face the speaker down and play

    Hold the phone at 45–90° with the grille toward the floor, then run one 30-second eject cycle.

  5. 05

    Check clarity, then repeat

    Run the clarity chime. Still muffled? Repeat up to three cycles, then let the phone air-dry.

How Water Remove Sound Works

A loudspeaker is a piston: low-frequency sound makes the diaphragm travel further and pump air through the mesh.

Most phone drivers resonate between 150 Hz and 200 Hz. A 165 Hz sine wave drives the cone at full excursion 165 times a second, and every outward stroke pushes a puff of air through the grille.

That moving air breaks the surface tension holding droplets in the mesh. With the port facing down, gravity carries the loosened water away instead of letting it settle back; the pulsed Deep Water mode adds stronger pressure spikes for stubborn drops.

iPhone vs. Android: Speaker Tips

The same sound works on both, but the wet parts are not in the same place.

iPhone: the top earpiece used for calls is a separate speaker from the bottom grille. Most “how to eject water from iPhone” guides forget it — hold the phone upside down for one cycle so the earpiece faces the floor.

Android: USB-C phones often show a moisture warning and refuse to charge. The tone clears the speaker, not the port — keep the port facing down to drain and wait for the alert to clear before plugging in.

Apple Watch: it uses its own water-eject tone and a purpose-built speaker. This tool is tuned for phone, tablet and laptop drivers, so use the watch’s built-in Water Lock instead.

Safety Tips: What Not to Do

The tone itself is safe. Most water damage comes from what people try next.

  • No hairdryers or ovens. Heat pushes moisture deeper and can warp the seals and the battery.

  • No rice. Uncooked rice sheds starch dust that clogs the speaker mesh and the charging port.

  • No compressed air. It forces water past the mesh instead of pushing it out.

  • No pins, toothpicks or cotton buds. The mesh tears easily and cannot be repaired.

Frequently Asked Questions

Does the water eject sound really work?

Yes, for water trapped in the speaker grille. It cannot dry the inside of a phone, so if the device was submerged or will not power on, have it serviced.

How loud should the volume be?

As loud as the phone allows, with Bluetooth off and Silent mode disabled. A quiet tone cannot move enough air to break the water film over the mesh.

How many cycles should I run?

One to three 30-second cycles, resting a minute between them. If the sound is still muffled after that, let the phone air-dry for a few hours and try again.

My microphone sounds muffled too — will this fix it?

The tone clears the speaker and the bottom microphone mesh, but not the internal microphone. If calls still sound distant after drying, the mic mesh may need professional cleaning.

Can I use it to clean dust from the speaker?

Yes. Choose Dust Clean, which sweeps 200–350 Hz, and brush the grille with a dry soft brush afterwards. Run it with the speaker facing down.

Is it safe on any phone, tablet or laptop?

It is ordinary audio at normal levels, so it is safe on phone, tablet and laptop speakers. Keep sessions short, stop if a device gets warm, and never use it on a device that is still wet inside.